Best Wireless Charger for Google Pixel 10a (2026)
The Pixel 10a charges wirelessly at up to 10W on a Qi-certified EPP charger. There is no Pixelsnap magnet in the phone. A 15W or 25W puck does not raise that cap.
The pad I would use is the Anker PowerWave II, A2519. Anker’s manual rates wireless output at 15W maximum, from a 12V 2A input, on a 90 × 90 × 13 mm pad. The phone still stops at 10W. The fast 30-minute result, about 50%, is a wired test on a 45W PPS charger.
Our Top Picks at a Glance
Reviewed September 2026 · Independently tested by our editorial team
Qi pad, 15W max on Anker’s manual. This phone caps at 10W. No magnets.
Check Price at Amazon Read full review ↓Qi pad. Anker’s 10W list is specific phones. Other Qi phones are listed at 5W.
Check Price at Amazon Read full review ↓Disclosure: This page contains affiliate links. As an Amazon Associate affiliate, we earn a small commission from qualifying purchases at no extra cost to you.
How We Tested
Google’s spec is the cap: 10W on a Qi EPP charger, no Pixelsnap. A2519’s manual is a 15W maximum Qi pad. A2503’s chart puts unlisted Qi phones at 5W. A 25W Pixelsnap puck was not counted as this phone’s charger.
Best Wireless Chargers for the Pixel 10a
PowerWave II Pad (A2519) View on Amazon
| Model | A2519 |
|---|---|
| Anker manual | Input 12V 2A, wireless output 15W max, 89 g |
| Phone cap | 10W on a Qi EPP charger |
| Alignment | Center it. The phone has no snap |
A2519 is a Qi pad. Anker says it switches among 5W, 7.5W, 10W, and 15W based on the phone, and the manual caps the pad at 15W. Google caps the Pixel 10a at 10W with a Qi-certified EPP charger. The extra 5W on the pad is unused. There is no magnet, so set the phone in the middle of the ring markings and check that it is actually charging. A thick case can make that handshake worse. The 50% in 30 minutes figure will not come from this pad. That number is the wired 45W PPS test.
- Qi pad with a 15W rating
- No magnet myth
- Small
- You align it yourself
- Will not beat 10W
- Not the 30-minute wired test
Anker 313 (A2503) View on Amazon
| Model | A2503 |
|---|---|
| 10W mode | Anker lists specific Samsung phones, with a QC adapter |
| Other Qi phones | Anker lists them at 5W |
| Skip if | You wanted the phone’s 10W EPP cap |
A2503 is the plain Qi pad. Anker’s own chart puts 10W on a list of Galaxy phones when the adapter is Quick Charge, and puts other Qi phones at 5W. The Pixel 10a is not that Galaxy list. I would not buy A2503 expecting Google’s 10W. It is the bedside pad if 5W overnight is enough. It has no magnets either. Input on Anker’s page is 5V at 2A or 9V at 2A.
- Simple
- Fine overnight if 5W is acceptable
- No magnet hardware to misunderstand
- Anker’s chart leaves other Qi phones at 5W
- Below the phone’s 10W cap
- Still needs a wall adapter
10W is the whole wireless story
Comparison Table
| Pick | Best for | Host | Skip if |
|---|---|---|---|
| A2519 | Qi pad at the phone’s cap | Pixel 10a, 10W | You need 50% in 30 minutes |
| A2503 | Overnight trickle | 5W on Anker’s other-Qi line | You wanted 10W |
Frequently Asked Questions
How fast is wireless charging on the Pixel 10a?
Up to 10W with a Qi-certified EPP charger. Google does not list Pixelsnap for this phone.
Will A2519 charge it at 15W?
The pad is rated to 15W. The phone’s published cap is 10W. The pad does not get to keep the extra 5W.
Does a magnetic case make it Pixelsnap?
No. ACS11282 and ACS11276 add a ring for accessories. The phone’s wireless rate stays 10W.
What reaches 50% in 30 minutes?
A 45W USB-C PPS wall charger or higher, in Google’s wired test. The cable is in the box. The brick is not.
Final Verdict
A2519 is the Qi pad for a Pixel 10a, and the phone still caps at 10W. A2503 is the slower pad Anker rates at 5W for Qi phones outside its 10W list. GH5UG does not add 25W to this phone. The 50% in 30 minutes result is wired, on a 45W PPS charger such as GW8L7.