Best HDMI Switch for Nintendo Switch and PS5 Monitors (2026)
A shared monitor has one HDMI input and two consoles that do not speak the same HDMI rate. Nintendo’s original Switch and the OLED model output up to 1080p through the dock’s HDMI port, with 5.1-channel LPCM. Switch 2’s TV mode goes higher: up to 3840×2160 at 60 fps, or 120 fps when the output is 1920×1080 or 2560×1440, plus HDR10. Sony’s PS5 support page says the console supports HDMI 2.1 and 4K at 120 Hz, and that a receiver or other box in the middle of the cable can change that signal. The cable Sony asks for is the one in the PS5 box, or an Ultra High Speed cable rated for 4K at 120 Hz, into an HDMI port that actually supports HDMI 2.1.
For that PS5 path, start with the Cable Matters 2-port 8K HDMI switch (103100). The manual prints 48 Gbps, one HDMI OUT, and two HDMI IN ports. Resolution support goes up to 4K at 120 Hz, 4:4:4, 12-bit, or 8K at 60 Hz. The feature line includes HDCP 2.3, HDR, HDR10, HDR10+, Dolby Vision, HLG, VRR, ALLM, and QFT. A center button swaps inputs. Holding it for 3 seconds toggles auto switching. Power is bus power, with an optional Micro USB port at 5 V / 1 A. The manual’s cable limit is 2 meters (6.6 feet).
Our Top Picks at a Glance
Reviewed October 2026 · Specs checked against Nintendo, PlayStation, and the manufacturers’ pages
48 Gbps. 4K120 4:4:4 12-bit. VRR and ALLM on the feature list.
Check Price at Amazon Read full review ↓48 Gbps, four HDMI inputs, and a remote. The 5 V adapter has to stay plugged in.
Check Price at Amazon Read full review ↓HDMI 2.0, 4K60 YUV 4:4:4, three inputs, and a remote. No 120 Hz line.
Check Price at Amazon Read full review ↓Disclosure: This page contains affiliate links. As an Amazon Associate affiliate, we earn a small commission from qualifying purchases at no extra cost to you.
How We Tested
Console output comes from Nintendo’s Switch and Switch 2 tech-spec pages and from Sony’s PS5 resolution guide. Switch figures come from the Cable Matters 103100 manual, OREI’s BK-401 support article dated July 4, 2026, the BK-401 manual’s resolution table, and J-Tech Digital’s resource page for JTECH-SW31. A switch stayed in only when those pages print a model number and a resolution ceiling.
The switches
Cable Matters 2-port 8K HDMI switch (103100) View on Amazon
| Model | 103100. The retail listing is often marked 103100-N |
|---|---|
| Ports | Two HDMI IN, one HDMI OUT. The cover says “1×2”; the diagram is two sources into one display |
| Bandwidth | 48 Gbps |
| Video | Up to 8K at 60 Hz, 4:4:4 10-bit, or 8K at 60 Hz 4:2:0 12-bit, or 4K at 120 Hz, 4:4:4, 12-bit |
| Features | HDCP 2.3, HDR, HDR10, HDR10+, Dolby Vision, HLG, VRR, ALLM, QFT |
| Power | Bus-powered. Optional Micro USB, 5 V / 1 A. That cable is not in the manual’s parts list |
| Warranty | Limited one year, on the manual |
This is the switch that matches Sony’s 4K 120 Hz line and Nintendo’s Switch 2 120 fps line at 1080p or 1440p. The manual’s feature list includes VRR and ALLM, which is what the PS5 support page is talking about when it says VRR needs an HDMI 2.1 display. Original Switch and OLED Switch docks stop at 1080p, so they sit inside the same box without using the 48 Gbps. Switch 2’s 4K mode is 60 fps on Nintendo’s sheet, and its 120 fps modes are 1080p or 1440p. Both fit a switch whose ceiling is 4K120 and 8K60, provided the monitor port and the cables do too.
Operation is on the center button. A press changes the input, and the green input LED shows which one is live. Holding the button for 3 seconds toggles auto switching: the LEDs blink three times when auto is on and five times when it is off. The manual says the switch is bus-powered and that some devices still need the Micro USB port tied to a charger or a free USB port on the display. For 4K at 120 Hz or 8K, it also says to use a supported port on the display, and to keep HDMI cables at or under 2 meters. Flicker is the manual’s cue to shorten the cable. Advanced HDMI features, it adds, have to be turned on in some television menus.
Audio on the spec list includes LPCM, Dolby Digital, Dolby TrueHD, Dolby Atmos, DTS, DTS-HD Master Audio, and DSD. Color depth is 8-bit, 10-bit, and 12-bit. The product page for this family also describes a two-pack of rated HDMI cables and auto switching. The manual is the page that sets the 2 meter cable limit and says the Micro USB cable is not included. HDCP 2.3 is on the feature list, so PS5 apps that require HDCP still see a compliant hop.
- 48 Gbps, with 4K120 4:4:4 12-bit printed in the manual
- VRR, ALLM, and QFT are on the same feature line as HDCP 2.3
- Two inputs match a Switch dock and a PS5 on one monitor
- Auto switching can be turned off with a 3-second hold
- The manual caps HDMI cables at 2 meters
- The Micro USB lead is optional and not included
- The cover text “1×2” reads like a splitter until you use the IN and OUT labels
- Only two sources. A PC needs a different box
OREI 8K 4-port HDMI switch (BK-401) View on Amazon
| Model | BK-401 |
|---|---|
| Ports | Four HDMI inputs, one HDMI output. OREI says it is not bi-directional |
| Bandwidth | 48 Gbps, HDMI 2.1, HDCP 2.3 |
| Video, manual | 8K at 60 Hz 4:4:4, and 4K at 120 Hz 4:4:4 10-bit, among the lines in the manual table |
| Features | HDR, HDR10, HDR10+, Dolby Vision, HLG, VRR, FVA, ALLM |
| Power | Included 5 V / 1 A adapter on the DC 5 V port. OREI says it must be connected |
| Control | Front INPUT button, or IR remote buttons IN1 through IN4 |
OREI’s July 4, 2026 support article is the operating guide. The BK-401 is a 4×1 switch: four sources, one display, with the output on the side panel. The included 5 V / 1 A adapter goes into DC 5 V before you use it. A short press of INPUT cycles 1, 2, 3, 4. A long press of about 3 seconds turns auto switching on, and the AUTO LED lights. The remote jumps straight to IN1, IN2, IN3, or IN4. OREI also says a black screen of a second or two while the display finishes the handshake is normal, and that this is not a seamless switch.
Auto mode watches the HDMI 5 V pin. A source that stays in standby and keeps sending 5 V still looks “on.” OREI’s own example is an Apple TV that holds the input after the PS5 is turned off, and then fails to release it when the PS5 wakes, because the Apple TV never dropped 5 V. The same note covers Fire TV, Roku, and Chromecast. With a Switch dock and a PS5, use the button or the remote when auto mode grabs the wrong input. The support article lists PlayStation 5 and Nintendo Switch among compatible sources, and it says 4K at 120 Hz or 8K still requires the source, the display, the cables, and the source’s video setting. Its cable line for those rates is an Ultra High Speed certified HDMI 2.1 cable under 15 feet.
The manual’s 4K120 line is 4:4:4 at 10-bit. The support article says 4K at 120 Hz, 4:4:4, without repeating the 10-bit figure. Plan on the manual’s 10-bit line. That is still inside a PS5 4K120 signal, and it is a step under the 12-bit 4K120 line in the Cable Matters 103100 manual. VRR and ALLM are on both OREI pages. HDCP stays on: OREI says the switch will not strip HDCP for a capture card. Audio through HDMI includes LPCM, Dolby TrueHD, DTS-HD Master Audio, and DSD.
- Four inputs, so a PC or a streaming box can share the monitor
- 48 Gbps, with VRR and ALLM on OREI’s list
- The remote selects an input by number
- The 5 V / 1 A adapter is in the box
- The adapter has to stay connected
- The manual’s 4K120 line is 4:4:4 10-bit
- Auto switching follows HDMI 5 V, so a standby box can hold the input
- OREI describes a short black screen on every switch
J-Tech Digital 3×1 HDMI switch (JTECH-SW31) View on Amazon
| Model | JTECH-SW31, resource SKU JTD-496 |
|---|---|
| Ports | Three HDMI inputs, one HDMI output |
| Video | Maximum 4K at 60 Hz, YUV 4:4:4. HDMI 2.0. HDR10 is a separate line on the spec table |
| HDCP | HDCP 2.2 or HDCP 1.4, chosen from the display |
| Power | 5 V DC adapter in the box. The page lists 182 mA at 480p60 and 277 mA at 4K60 |
| Size | 125 × 64.2 × 17 mm |
| Warranty | One-year replacement, on J-Tech’s feature list |
J-Tech’s resource page for JTECH-SW31 stops at 4K60. There is no 120 Hz line and no VRR line. That matches a monitor that never asks the PS5 for 4K at 120 Hz. Sony’s 120 Hz output and VRR settings need an HDMI 2.1 path, so this switch is the wrong box when the monitor’s HDMI port is the 4K120 one. Original Switch 1080p and Switch 2’s 4K at 60 fps are inside a 4K60 ceiling. Switch 2’s 120 fps modes, at 1080p or 1440p, are outside the resolution this page prints.
The package list is the switch, a 5 V DC power adapter, a user manual, and an IR remote. The setup line says to use the front button or that remote after the adapter is connected. HDR10 and CEC are in the functions list. HDCP follows the display, 2.2 or 1.4. The feature bullets also name Dolby Digital Plus, Dolby Atmos, and DTS:X. One marketing sentence on the same page says “ZT-SW31.” The model field and the package list both say JTECH-SW31, so that is the part to search.
Operating range on the page is −5 °C to 40 °C. A one-year replacement warranty is what J-Tech prints, with weekday support hours listed as 9 AM to 6 PM CST. Use this when the monitor spec is 4K60 and you want a third HDMI input with a remote. Move to the 103100 or the BK-401 when the PS5 is set to 4K at 120 Hz or VRR.
- Three inputs and a remote on a 4K60 HDMI 2.0 switch
- HDR10 and HDCP 2.2 are on the spec table
- The 5 V adapter is in the package list
- 1080p from an original Switch dock is inside the printed maximum
- The maximum on the page is 4K at 60 Hz
- VRR and 4K at 120 Hz are not in the spec table
- Switch 2’s 120 fps output is outside that maximum
- A feature sentence uses a different model string than the package list
Match the console’s HDMI line, then the monitor port
Comparison Table
| Switch | Inputs | Printed ceiling | Power |
|---|---|---|---|
| Cable Matters 103100 | 2 | 48 Gbps, 4K120 4:4:4 12-bit, VRR, ALLM | Bus power, optional Micro USB 5 V / 1 A |
| OREI BK-401 | 4 | 48 Gbps, 4K120 4:4:4 10-bit in the manual, VRR, ALLM | Included 5 V / 1 A, required |
| J-Tech JTECH-SW31 | 3 | HDMI 2.0, 4K60 YUV 4:4:4, HDR10 | Included 5 V DC adapter |
Frequently Asked Questions
Will a switch keep the PS5 at 4K 120 Hz?
Sony says the PS5 supports HDMI 2.1 and 4K at 120 Hz, and that equipment between the console and the display can affect that signal. The 103100 manual prints 4K at 120 Hz, 4:4:4, 12-bit, at 48 Gbps, and lists VRR. The BK-401 manual prints 4K at 120 Hz, 4:4:4, 10-bit, at 48 Gbps, and OREI lists VRR. JTECH-SW31’s maximum is 4K at 60 Hz. The monitor port and the cables still have to match the rate you set on the PS5.
Does the original Switch need HDMI 2.1?
Nintendo’s spec for the original Switch and the OLED model is up to 1080p via HDMI in TV mode. That signal fits every switch on this page. Switch 2 is the console whose TV mode lists 4K at 60 fps and 120 fps at 1080p or 1440p. The Switch Lite has no HDMI output, so it is not part of this setup.
Why does auto switching stick on the wrong console?
On the BK-401, OREI says auto mode detects the HDMI 5 V line. A device that stays in standby and keeps sending 5 V still looks active, and the switch may not move when the PS5 turns on. Use the front button or the IN1–IN4 remote. On the 103100, hold the center button for 3 seconds if you want auto switching off. The LEDs blink five times when it is disabled.
Can the same box feed a capture card?
OREI says the BK-401 is HDCP compliant and will not bypass HDCP-protected content for a capture card. The 103100 manual lists HDCP 2.3. These switches are for a monitor, and HDCP stays in the path.
Final Verdict
The 103100 is the two-console switch: 48 Gbps, 4K at 120 Hz at 4:4:4 12-bit, and VRR on the manual, with cables kept to 2 meters. The BK-401 is the same class of bandwidth with four inputs and a remote, and it only runs with the included 5 V adapter. The JTECH-SW31 is the 4K60 HDMI 2.0 switch, and it leaves PS5 120 Hz and VRR on the other two boxes.